ASTM D1204 PDF
This standard is issued under the fixed designation D ; the number relevant ASTM material specification shall take precedence. GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D,Standard Test Method for Linear Dimensional Changes of Non-rigid. ASTM D Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature.
|Country:||Trinidad & Tobago|
|Published (Last):||7 October 2014|
|PDF File Size:||12.11 Mb|
|ePub File Size:||4.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes.
Send us a request Wilton UK: This standard has been approved for use by agencies of the Department of Defense. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The dimensions of the specimen are taken at reference marks.
Need help or have a question? Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world. After removal from the oven, the specimens are reconditioned at room temperature for a minimum of one hour.
Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the relevant ASTM material speci? NOTE 2—The paper should be well dusted, and the specimens should not be restricted either by the paper or the clips. Auditing Consulting Sourcing Training. Validating the specifications, value and safety of your raw materials, products and assets.
Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world. The sandwiched specimens are placed in an oven for a specified amount of time. Testlopedia – The Plastics Testing Encyclopedia. Fasten the papers together with paper clips.
Table 1 of Classi? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Percent linear change is equal to final length minus original length divided by original length multiplied by The test is mostly used for sheeting or film made by extrusion or calendar processes.
The test gives an indication of lot-to-lot uniformity with regards to internal stress introduced during processing.
Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes.
NOTE 1—This test method and ISO address the same matter, but differ in technical content and results cannot be directly compared between the two methods. Remove the papers and measure the distance between the opposite edges of the specimens at the reference marks to the nearest 0.
Dimensional Stability ASTM D
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Points a, b and x, y are reference marks at midpoint of test specimen edges.
The distances between the reference marks are re-measured and recorded. Send us a request Need help or have a question?
Active Risk Management
The midpoint of each edge shall be marked for use as a reference point when? Assurance Testing Inspection Certification. Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. Standards can be obtained from appropriate standards authorities. The test gives an indication of lot-to-lot uniformity as regards to the degree of internal strains introduced during processing.
Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
ASTM D 尺寸变化率_百度文库
A negative value denotes shrinkage, and a positive value indicates expansion. Current edition approved Nov. Formally confirming that your products and services meet all trusted external and internal standards.
Dimensional Stability is a measurement of the linear dimensional change resulting from exposure to temperature. Last d120 edition approved in as D f1204 Originally approved in If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. It is imperative that the specimens be free to change shape as strains are relieved during the period of test. Precision and Bias Each specimen shall be marked to show the direction of calendering or extrusion.
Sandwiches must not be stacked, as this may restrict movement of the plastic between the papers. Inspection Validating the specifications, value and safety of your raw materials, products and assets. Talc awtm paper is inserted to form a sandwich around the specimen. A number in parentheses indicates f1204 year of last reapproval.
November 1, 1 Revised Section 7 and 8. ASTM D – Certification Formally confirming that your products adtm services meet all trusted external and internal standards. Shorter reconditioning times may be used if it can be shown that equivalent results are obtained.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.