DMO565R DATASHEET PDF

0 Comments

DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Mauk Mikahn
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Finance
Published (Last): 1 April 2008
Pages: 61
PDF File Size: 10.16 Mb
ePub File Size: 6.29 Mb
ISBN: 377-5-42441-923-4
Downloads: 18855
Price: Free* [*Free Regsitration Required]
Uploader: Jutilar

During start up, the power is supplied by an internal high voltage current source that is connected to the Vstr pin.

This pin is the positive supply voltage input. Excessive voltage across the Rsense resistor would lead to incorrect feedback operation in the current mode PWM control.

Because these protection circuits are fully integrated into the IC without external components, the reliability can be improved without increasing cost. This pin is connected directly to the high voltage DC link. If the voltage of this pin reaches 6. The PWM controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking LEBoptimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation and self protection circuitry.

Free standing with no heat-sink under natural convection. The collector of an opto-coupler is typically tied to this pin.

DMO565R PDF

If the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero. Maximum practical continuous power in an open frame design at 50C ambient.

  LDF4RK 50A PDF

Pulse width modulation PWM circuit2. Therefore, the peak value of the current through the Sense FET is limited. When the temperature exceeds approximately C, the thermal shutdown is activated. Cdbe datasheet pdf – datasheet pdf Cdbe datasheet pdf In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. TempBurst Mode Enable Voltage vs. In this generation the startup resistor is replaced by an internal high voltage current source.

DMOR PDF –

This device is a basic platform well suited for cost effective designs of flyback converters. TempFeedback Source Current vs. The voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output voltage. This pin is the control ground and the Sense FET source. This causes Vcc to fall. Overload is defined as the load current exceeding a pre-set level due to an unexpected event.

At startup, the internal high voltage current source supplies internal bias and charges the external capacitor that is connected to the Vcc pin.

Since D1 is blocked when the feedback voltage Vfb exceeds 2.

This pin is internally datasheeh to the inverting input of the PWM comparator. The feedback voltage then falls and the process repeats. These parameters indicate the inductor current.

DMR Datasheet, PDF – Alldatasheet

If the output consumes beyond this maximum power, the output voltage Vo decreases below the set voltage. The typical soft start time is 10msec, The pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, inductors, and capacitors.

  DICCIONARIO TEOLOGICO DEL NUEVO TESTAMENTO KITTEL PDF

This causes the feedback voltage to rise.

At startup, an internal high voltage current source supplies the internal bias and charges the external datwsheet Cvcc that is connected to the Vcc pin as illustrated in Figure 4.

SN datasheet – Texas Instruments Documents.

An opto-coupler such as the H11AA and shunt dayasheet such as the KA are typically used to implement the feedback network. In order to avoid this undesired operation, the over load protection circuit is designed to be activated after a specified time to determine whether it is a transient situation or an overload situation. Qlt datasheet pdf – datasheet pdf QLT datasheet, This event typically happens when the input voltage is increased or the output load is decreased.

Rockchip RK datasheet V0.

In this situation, the protection circuit should be activated in order to protect the SMPS. This reduces the current through the opto-coupler LED, which also reduces the opto-coupler transistor current, thus increasing dmo556r feedback voltage Vfb. The delay time for shutdown is the time required to charge CB from 2.

Published on Apr View Typical continuous power in a non-ventilated enclosed adapter measured at 50C ambient.